Bull-X EGO downpipe Polo AW1 GTI 200hp (with ECE*) (HGDPBX007M)

BULL-X Exhausts produces downpipes at the highest level. The HG-Motorsport EGO downpipe for the Polo AW1 2.0 TSI is a 100% direct replacement for the factory part. Perfect fit and high-quality materials make this item a top product in our range. By optimising the diameter, pipe routing and/or catalytic converter, the load on the turbocharger can be greatly reduced. On the EGO downpipe, the entire upper section and the lower section up to the flex pipe are cast completely in one piece. After the 84mm turbocharger outlet, the downpipe widens to a diameter of 121mm and, thanks to flow analyses calculated in 3D, delivers the maximum exhaust flow, which can be turned into reality with just a single cast part. Lower back pressure and reduced thermal load produce a clear gain in torque, power and earlier response, while at the same time extending durability. Note: on vehicles with a manual gearbox we recommend using the reinforced torque mount, as the original mounts wear out very quickly and the larger pipe diameter could otherwise lead to contact/noise.

Technical details:

• - Upper and lower sections up to the flex pipe in one piece of cast stainless steel - After the 84mm turbo outlet, the downpipe widens to a diameter of 121mm!!! - made of stainless steel - fully TIG-welded - optional: with integral insulation (see last product image) - * optionally without catalytic converter, incl. 100-cell sports cat, incl. 200-cell sports cat, with Bull-X 200-cell EOBD sports cat by HJS, with 200-cell HJS sports catalytic converter incl. ECE operating licence - incl. stainless steel reducer for easy fitting to the factory system - Also fits Bull-X/EGO-X exhaust systems plug and play Caution: regardless of the cat variant, this downpipe only fits Polo AW1 models with an oxidation cat, not vehicles with an OPF (petrol particulate filter) from model year 2019 If a catalytic converter variant without ECE approval is selected, the following applies to this item: This item is not approved for use on public roads - For racing purposes only! CAUTION! All catalytic converters/cat replacement pipes offered, except the EC-tested catalytic converter from HJS, are not approved under the German road traffic regulations! Only with the EC catalytic converter may you legally drive your vehicle on public roads. The use of all other catalytic converters is intended for racing purposes only. If, despite our notice, you fit a downpipe with a catalytic converter WITHOUT EC approval, you are committing a criminal offence. Possible consequences include: invalidation of the operating licence, decommissioning of the vehicle, a complaint for tax evasion and possible investigations by the environmental authority. Catalytic converter information If you select a downpipe without a cat or with a 100/200-cell cat, the control unit may log an error message from the post-cat lambda sensor; this does not restrict driving, as the first lambda sensor is still there for engine management. The post-cat sensor is only responsible for monitoring the cat’s effectiveness. This can be programmed out by a chip tuner by adapting the software. Most vehicles up to the Euro 3 emissions standard have no post-cat oxygen sensor, and installation is possible without further adaptation and without error messages. The washcoat content of HJS ECE and EOBD cats is significantly higher and is characterised by a very high oxygen storage capacity, which means error messages can be avoided. The EOBD cats have been tested for this up to Euro 4. Durability and use up to the Euro 6 emissions standard are of course guaranteed. On Euro 5/6 vehicles, the points mentioned above can only be avoided if a cat with ECE approval is selected. For more information on emission classes and how a catalytic converter actually works, please click here. The following cats are fitted in the downpipe with ECE operating licence: pre-cat and main cat

TÜV / ABE available upon request

We currently ship within Europe only.

If a part is not available, we will contact you with an estimated wait time.

If you wish to return a product after receiving it, we offer a 14-day returns policy. Custom-made products are not eligible for return, and return shipping is at the customer's expense. Full delivery and returns terms are on the “Delivery Information” page — the link is at the bottom of the page.

Products come with a warranty, detailed in a certificate included in the box.

To make a valid claim, you must prove the damage was not caused by you and that the warranty certificate is valid.

Full terms are on the “Terms & Conditions” page — the link is at the bottom of the page.